• ONA-800 SA module tests recommended with GPS/GNSS

    Questions   When performing testing with my ONA-800 SA module, is it recommended that the unit have GPS/GNSS sync? Answer   GPS sync is required for Gated sweep, Interference Finder, Route Mapping and Rad...
    viavisupport
    last modified by viavisupport
  • Real-Time Spectrum Analysis with the ONA-800 SA module

    Questions   What is the difference between the spectral analysis being performed under Spectral Analyzer and Real-Time Spectrum Analyser? Answer   The Spectral Analysis graph allows you to see how the lev...
    viavisupport
    last modified by viavisupport
  • ONA-800 SA module RFoCPRI versus Over the Air Spectrum Analysis

    Questions   What is the value in performing RFoCPRI analysis as opposed to normal Spectrum Analysis via an attached antenna? Answer   Including RFoCPRI is recommended as you are viewing the spectrum as re...
    viavisupport
    last modified by viavisupport
  • Viewing CPRI power and alarms on the ONA-800 SA module

    Questions   When performing CPRI analysis on my ONA-800 SA module, where do I go to see my receive power and signal state? Answer   Power level and signal/alarm status can be view by selecting PORT CONFIG...
    viavisupport
    last modified by viavisupport
  • ONA-800 SA  PIM detection versus Interference Analysis

    Questions   How is interference caused by PIM different than the interference detected in the SA Interference Analysis? Answer   Testing performed in Interference Analysis is for detecting interference at...
    viavisupport
    last modified by viavisupport
  • VIewing a .grrv file on the ONA-800 Spectrum Analyzer

    Questions   What is a .grrv file, on my ONA-800 SA module and how can it be viewed? Answer   The .grrv file is a log file that is created under Interference Analysis by selecting SAVE and then LOGGING....
    viavisupport
    last modified by viavisupport
  • ONA-800 SA Gated Sweep

    Questions   When is a Gated Sweep used when performing RF Spectral Analysis? Answer   A Gated Sweep is used when looking for interference on Time Division Duplex (TDD) RF signals. As the uplink and downli...
    viavisupport
    last modified by viavisupport
  • ONX-220 Quick Start Guide

    Document Name ONX-220 Quick Start Guide.pdf
    viavisupport
    last modified by viavisupport
  • ONX-220 User Guide

    Document Name ONX-220 User Guide.pdf
    viavisupport
    last modified by viavisupport
  • FI-60 Not displaying tone on fiber

    Solution    My FI-60 LFI head is not detecting my tone on the fiber. Instead of displaying the tone frequency, it just says TRAFFIC.  Problem  This can happen if the jacket of the fiber jumper is quite thick. Try...
    viavisupport
    last modified by viavisupport
  • XperTrak 4.0 Quick Start Guide 061220 Rev 006

    Document Name XPERTrak 4.0 Quick Start Guide 061220 Rev 006.pdf
    viavisupport
    last modified by viavisupport
  • SCU-1800 Getting Started Guide

    Document Name   SCU-1800 Getting Started Guide-22114998_rev002_.pdf
    viavisupport
    last modified by viavisupport
  • SCU-1800 Quick Card - Return Sweep Setup

    Document Name   SCU-1800 Setup Quick Card.pdf
    viavisupport
    last modified by viavisupport
  • Viavi CLEANBLAST Tip Selection Guide

    Document Name CleanBlast Tips Selection Guide May 2020.pdf
    viavisupport
    last modified by viavisupport
  • OneExpert CATV 620 Extended Quick Start Guide v12.1

    Document Name   OneExpert CATV 620 Extended Quick Start Guide v12.1.pdf
    viavisupport
    last modified by viavisupport
  • OneAdvisor ONA-800 Software Upgrade Procedure

    Document Name OneAdvisor ONA-800 software upgrade procedure.pdf
    viavisupport
    last modified by viavisupport
  • OneAdvisor ONA-800 Calibration Requirements

    Questions   What the routine calibration requirements for the OneAdvisor ONA-800 platform and supported modules? Answer   The ONA-800 base calibration interval is recommended for 2 years unless used in co...
    viavisupport
    last modified by viavisupport
  • Typical Values for VSWR testing

    Questions   What VSWR values are generally considered to be acceptable,  when performing Cable and Antenna Analysis? Answer   A perfect VSWR value, when there would be no reflected power, would be a...
    viavisupport
    last modified by viavisupport
  • Seeker MCA III Install Guide Spanish Rev 001

    Document Name   Seeker MCA III Install Guide 012720 Spanish Rev 001.pdf
    viavisupport
    last modified by viavisupport
  • Seeker MCA III Install Guide - German Rev 001

    Document Name   Seeker MCA III Install Guide 012720 German Rev 001.pdf
    viavisupport
    last modified by viavisupport